Incline Conveyor- Vecoplan
27′ long
6′ wide
11 – 12′ discharge height
5HP motor
74-1 gear ratio
FOB TN
Shop
Jeffrey Hammermill- 60HP
Jeffery Dresser 30WB Hammer Mill
SN 883474
Heavy Duty 25lb Hammers
60hp 3ph 1775 rpm Motor
Square D Soft Starter Panel
Mill was taken down in working order when business closed. Motor was sent
off and tested with a clean bill of health. Interior of the mill shows
little to no wear on wear liners and screens. Reversible hammers show
approx 10% wear on one side, and no wear on the other (never flipped). The
75hp Square D Start panel is secondary market, used in working condition.
Located in PA
Komatsu Auto Dismantler
2016 Komatsu PC210LC-10 crawler auto dismantler
8,776 hours
good undercarriage
new 2 tine/ tilting/ rotating/engine + wire harness pulling grapple with new open/ close + up/down hold down clamp
FOB PA
Large Cyclone, Fan and Ducting
Used in a large shredder system
Includes Fan
Piping in great shape
Had a 100+ HP motor
45,000 CFM
FOB WY
Liebherr 932 Material Handler with Grapple and Magnet
Around 20k hours
1999 year model
New engine about 10 years ago
Working grapple and magnet included
Was a primary handler and used daily until 3 months ago. Good condition and well kept maintenance
Liebherr LH60 Material Handler
21,000 hrs
Runs and operates fine
Swing motor starts to slow down when the oil gets hot
Located in NC
Linkbelt 360 Material Handler
Linkbelt 360
4 tine grapple
18,000 hours
Runs but has some issues
FOB NC
Lukas Handheld shear
Model- LSI- 400E
The LSI-400E is the ideal cutter for mobile application in scrap and
auto recycling yards. Operation of curved 5″ cutting blades is
through an electric push button control that operates a solenoid
valve on the power unit. With a cutting force of 35 tons the
LSI-400E has a cutting capacity of 0.91″ mild steel. This tool
requires the LUK-P06-LSI-510 power unit, LUK-84150-8088 hose
and LUK-84150-1361 Cart. Tool weight is 35lbs
Includes, Cutter, pump, hose and cart
Location: Indiana
MachineX 32′ sliderbed conveyor
Bi-Directional sliderbed
Length 32’8″
Width 36″
Good Condition. Can be shown under power
FOB TN
Metso M&J PreShred 4000
2023
Cat (C15)- 15k hours
Used to break about plastic bales- not ran hard
Heavy-Duty pre-shredder for bulky waste, C&D and white goods
Capacity- 100-125 tons/hr
New Alternator and batteries installed recently
PM’d regularly, hardfacing on teeth
Located in TN
MG Recycling 380VZT Cable Granulation Line
7700 hours (granulator has been replaced in the last few years with low hours)
Processes 2,000 lbs/hr
Steel belt infeed conveyor
60HP preshredder
Conveyor into granulator with magnetic head pulley
Upgraded 40HP granulator – low hours
Zig Zag separator
Turbo Mill
Separation table
Dust/Baghouse
Includes all duct work and some spare parts
Location- Texas
MG Recycling- Wire Granulator- MG150- Low Hours
45 total hours
350-650 lbs/hr depending on wire infeed
30 HP granulator
Includes Turbo Mill and Separation Table
Dust filters/collection
This unit can process small communication wire as well as all #1
There is a used Wagner single shaft shredder that can be sold separately.
Includes conveyor to feed granulator
Located in SC
