(2) Eriez Cross Belt Magnets
Permanent Suspended Magnet
Model- CP20/80SC2
Year- 2019
30″w x 72″l
One is missing a gearbox
FOB CT
Shop
(2) Volvo Dump Truck – 2017
2017 VOLVO VHD84B200 Quint Dump Truck
Mileage 364K
Volvo D11J405 6 Cylinder 10.8 L Diesel 405 hp Engine, 2016 US EPA Label, Requires Diesel Exhaust Fluid, Air Conditioner, Cruise Control, Engine Brake, Automated Transmission, Differential Lock, 20000 lb Front Axle, 40000 lb Rears, Meritor MT-40-14X Drive Axles, 3.90:1 Axle Ratio, 60000 lb GVWR, Air Ride Cab, Aluminum Wheels, 315/80R22.5 Front Tires, 11R22.5 Rear Tires, 3 Steerable Air Lift Pusher Axle, Dual Steering Boxes, Double Frame, Spring Suspension, 280 in Wheelbase, PTO, 17 ft Long Steel Body, Manual Roll Tarp, High-Lift Tailgate
2017 VOLVO VHD84B200 Quint Dump Truck
Mileage 304k
same specs as the above
Located in SC
100 HP Harris Dual Shaft Motor
Could be used on Gorilla, BSH Shear, etc.
Reliance 100hp, 1750rpm, 405ty, 460v/60hz Harris P#857537 Bench tested
FOB FL
120 HP Dual Shaft Shredder
2017
(2) 60 HP 3 phase motor
8’ x 4’ feed hopper opening
52” x 29” Shredding Chamber
Panel included (start/stop/reverse w/ auto reverse relay switch)
Machine is hooked to power
Machine was used to pre-shred light iron, tin, large copper wire. In November, ’23 both gear shaft broke. New shafts and chain sprockets come with the machine, they just need to be pressed in.
FOB PA
15 HP Dual Shaft Shredder
Purchased from a polyethylene bag manufacturer
In good working order
FOB TX
1984 Aljon 400
Used daily to bale cans.
Can be seen in operation.
Service records kept
FOB PA
1990 Portable ALJON 400 logger baler with crane and grapple
Serial number is 12924
The grapple was rebuilt in 2023
The door cylinders were rebuilt in 2023
The injection pump was rebuilt in 2023
All the cylinders were repacked and new main valve body.
FOB NY
1998 Aljon 400 Logger Baler
SN13586
Hour meter not working
On the backside of box- lid hinge is bent. Area below hinge has damage and should be addressed
Still working every day. Can be seen in operation
FOB SD
200 HP Turbo Mill
The CMTM-1500 turbo mill is designed to grind rigid and semi-rigid materials into a fine particle size smaller than 1/16″ in diameter. It’s especially apt at processing hair wires and fine strand materials.
Turbomill:
– 200hp TEFC 360/230/460 3ph electric motor.
– Carbon steel plate body.
– Easily interchangeable steel wear-plates and beater knives.
– Clam-shell design for easy opening.
CMBL-4:
-50hp blower W-VFD
-Cyclone
-Airlock
Controls Cabinet:
-200 HP VFD for Turbo*
-500 hp VFD for Blower*
-Motor starter for airlock
-5hp VFD for infeed hopper. (not included in sale price, but available)
*VFD needed to properly operate. (included)
A blower, cyclone, and air-lock valve are required in order to pull the material thru the Turbo Mill. (Included)
(New System would cost $275,000)
200 HP Williams Hammermill
200hp Williams Crusher Hammer Mill Shredder w/ Steel Foundation
Model 40KS
SN-17681
45lb Hammers
30″x40″ Solid Spider Rotors
Top Feed Hopper
Screen Size: 1 1/2″ x 3″
200hp World Energy Electric Motor
RPM: 1,175
Frame Size: 505UZ
3 Phase – 460v – 246amp
*No Panel Included*
Mill is in excellent condition, and was used up until the day the company closed the door. Hammers were replaced last year, and show very little sign of wear.
Can shred metals such as light iron/tin, electric motors, dirty aluminum, cast, etc.
*PLEASE NOTE*
The “catwalk” around this have been cut off due to oversized trucking limits.
FOB PA
2007 Aljon 580
Aljon 580 Logger Baler
Year: 2007
Seller believes there is around 6000 hours on unit.
Lots of new parts; DOT ready
FOB IA
